Apart from using the gas pedal, you can also access the oil life menu to reset the oil light on the 2016 grand cherokee or later. Push and hold the ‘ok’ button until the oil life gauge resets to 100%.
Turn the ignition to the “run” position.
How to reset oil change on jeep grand cherokee. Set the gear to park position. In the instrument cluster display, navigate to “vehicle info” then “oil life.”. Turn the ignition key on without starting the engine.
Yes it probably will be the sender. If necessary repeat this procedure. Now you are going to hold down the ok button until you see that the oil life display has changed to 100 percent.
All information is taken from the jeep grand cherokee owners manual. Set the gear to the park position. How do you reset the oil life on a 2017 jeep grand cherokee?
How do you reset the oil life on a jeep? Turn the ignition back to the on position while holding the reset button. After these steps have been performed, you have successfully reset the oil life on the jeep cherokee if you are unable to reset the “oil change required” light utilizing one of these methods, repeat the steps.
Use the navigation button in order to select vehicle info. The fastest way to reset oil life and is usually used for all jeep models is by step on the gas pedal three times slowly within 10 seconds after turn the ignition to the run position. If the indicator message still illuminates when you start the car, the oil change indicator system did not reset, and you will need to repeat this procedure.
In the instrument cluster display, navigate to “vehicle info” then “oil life.” push and hold the ‘ok’ button until the oil life gauge resets to 100%. Oil change light reset jeep cherokee 2015 procedure. Jeep / chrysler / fiat do not have a recommended oil change interval, they use the compu.
Fully depress the accelerator pedal slowly three times within 10 seconds and the oil change is reset. Immediately press and release the accelerator pedal 3 times within 10 seconds. If the indicator message illuminates when you start the vehicle, the oil change indicator system did not reset.
It’s suitable for 2015 to the 2021 jeep cherokees, but not sure if the motor makes a difference, i would assume it wouldn’t. Reset the ignition to its on position while pressing the button for reset. This also works for other mopar vehicles as w.
Allow the light to blink on and off for a few seconds, then release the reset button and turn the ignition off. How do you reset the oil life on a jeep? Let the light blink on and off for a short period of time and then release the reset button, and switch off the ignition.
Turn the ignition to the “run” position. Check the oil change or maintenance light closely. It will begin to blink.
Cheap insurance to protect your engine. Turn off the ignition and start the engine to make sure it worked. Without starting the engine, turn the ignition in the on/run mode position.
Changed the oil on my 2004 jeep grand cherokee a week ago and now check gage light is on a it says that the oil pressure is low, could it be the send oil pressure swith needs to be replaced. Turn the ignition to the run position. Without starting the engine, turn the ignition in the on/run mode position.
That it is the full procedure how to reset oil service light jeep grand cherokee. It should start to blink. Basically, you need to use the navigation buttons on the steering wheel to access the menus in the instrument cluster.
Oil change light reset jeep grand cherokee 2008 2009 2010 2011 2012 2013 2014 2015 procedure. Repeat the process if the indicator does not reset. Immediately press and release the accelerator pedal 3 times within 10 seconds.
Does anyone know how to reset the oil change due indicator? Jeep grand cherokee oil service maintenance reminder light. Without pressing the brake pedal, push the engine start/stop button and cycle the ignition to the on/ run position (do.
Turn ignition to run position, don’t start the engine. Push and hold the ok button until the oil light percentage changes to 100%. 2011 ford explorer limited fwd.
If you like to reset any maintenance. Press the start/stop button to turn the electronics off. I just did my engine oil change on my 2017 jeep cherokee with the 2.4 cylinders, and now i’m going to show you how to reset the oil life.
To reset the oil change indicator system (after performing the scheduled maintenance) refer to the following procedure. 2011 jeep grand cherokee overland 4×2, 3.6l v6 (partner's). Watch the oil change or maintenance light carefully.
Once there, find the remaining oil life.